Saw Blade Bin with Spent-Blade Pod - Backstage cart lip (one piece, strongest)
======================================================================

What it holds: Recip and 12 in hacksaw blade lanes with magnets, a utility-blade magazine, a sealed SPENT pod and a divided MISC well.

PRINT SETTINGS
  Filament:  PETG
  Walls:     5
  Infill:    35% gyroid
  Orientation: the files are already oriented for printing. Put them on the plate as they load;
               don't rotate them.

FILES AND SUPPORTS
  - H_RJ_blade_bin_lip.stl  (supports: no (unless your slicer warns))
  - H_RJ_blade_bin_lip_base.stl  (supports: no (unless your slicer warns))
  - H_RJ_blade_bin_lip_text.stl  (supports: no (unless your slicer warns))
  - RJ_spent_pod.stl  (supports: no)
      how it lies on the plate: upright, flat bottom on the bed, no supports (45 deg gable roof); print it red or orange
  - RJ_spent_pod_base.stl  (supports: no)
      how it lies on the plate: upright, flat bottom on the bed, no supports (45 deg gable roof); print it red or orange
  - RJ_spent_pod_text.stl  (supports: no)
      how it lies on the plate: upright, flat bottom on the bed, no supports (45 deg gable roof); print it red or orange
  - RJ_divider.stl  (supports: no)
      how it lies on the plate: flat on its face, no supports

HOW IT MOUNTS
  BACKSTAGE CART LIP (ONE PIECE, STRONGEST)
    The cart-lip slot is printed into the holder, so it is one piece and as strong as it gets.
    Hold it tilted, hook the slot over the upright lip on the edge of a Magliner / Backstage-style cart
    shelf, and rock it down until it sits flat against the side.

    Notes for this holder: One piece with the Magliner/cart lip block across the back: bin bottom level with the deck, top 0.4 above the block. Optional M5 lip clamps. Prints upright on its flat bottom, no supports; 328 mm long like the shipped bin. ~508 g. Plus the SPENT pod and 3-5 dividers. Two-colour labels: print <name>_base + <name>_text together as one object (same placement); one colour: the plain file.

HOW IT WORKS
  Loose saw blades are sharp, hard to sort and like to fall off a cart. This 328 mm bin puts each kind in its own lane and holds them down with magnets.

  - RECIP lane (14 x 15 mm): reciprocating-saw and compact-saw blades (fits Milwaukee Sawzall and Hackzall blades) up to 12 in, stood on edge with the backs up 4-10 mm proud, so you can pinch one out anywhere
  - HACK lane (8 x 9.5 mm): 12 in hacksaw blades
  - Magnets: 6 x 3 mm magnets in both lane floors hold the steel blades on bumps (one drop of CA glue each, pressed in with a plastic or wooden stub). Three finger scoops in the front wall let you lift a blade with one hand
  - UTILITY magazine: about 12 trapezoid utility blades on edge, with a magnet
  - SPENT pod: a little red blade bank with a 45 degree roof and a 1.6 mm slot. Drop used blades in and they cannot fall back out. When it rattles full, tape the slot, bin the whole pod and print another (about 18 g)
  - MISC well: 22 x 169 x 30 mm with 5 slots for drop-in dividers. Use it for drill bits, snap-off blades, pencils and hole-saw pilots
  Labels: SPENT / UTILITY / MISC on the front, RECIP / HACK on the lane ends.
  Mounting (DOCK system): the back carries two DOCK tongues 60 mm apart. Drop it into two DOCK adapters (Magliner / Backstage lip, ToughBuilt bar, round or square tube, T-slot, all in the DOCK system listing) and it clicks in. To take it off, push the release pad with your thumb and lift. Riding a truck lift gate: fit both M5 lock screws (2 per twin holder). Print the DOCK coupon first.
  Cart facts (on two lip adapters)

  - Sticks out 73 mm from the cart side
  - Top sits 34 mm above the deck; lowest point 8 mm below it
  - Overall 64 x 328 x 43 mm (out x along x up), tongues included

OTHER MOUNTS
  The same holder also comes ToughBuilt bar (one piece), Dock (swap between mounts), Mountless (desk, shelf, case or screw to a panel). Pick the mount on the site: https://cart-tools.sdos-placeholder.workers.dev/#rj-blade-bin

TEST THE FIT FIRST
  Carts, bars and tape rolls vary a little. Before a long print, print the small fit test from the
  Test pieces section of the site (or this part at low infill) and check it on your own gear.

Not affiliated with or endorsed by Magliner, Backstage Equipment, ToughBuilt, Milwaukee, Hollyland, Eartec, Sekonic, Inovativ, Matthews or Manfrotto. Brand names only say what a holder fits.
