Nitrile Glove Box Holder - Backstage cart lip (one piece, strongest)
====================================================================

What it holds: Nitrile glove box up to 233 x 66 (spacers for 218-221 x 61)

PRINT SETTINGS
  Filament:  PETG
  Walls:     5
  Infill:    35% gyroid
  Orientation: the files are already oriented for printing. Put them on the plate as they load;
               don't rotate them.

FILES AND SUPPORTS
  - clip_LC_std_glove_box_sleeve_std.stl  (supports: no)
  - clip_LC_spacer_std_glove_spacer_std_6mm.stl  (supports: no)
  - clip_LC_endblock_std_glove_end_spacer_std_13mm.stl  (supports: no)
  - clip_LC_tag_S_glove_size_tag_S.stl  (supports: no)
  - clip_LC_tag_M_glove_size_tag_M.stl  (supports: no)
  - clip_LC_tag_L_glove_size_tag_L.stl  (supports: no)
  - clip_LC_tag_XL_glove_size_tag_XL.stl  (supports: no)
  - clip_LC_long_glove_box_sleeve_long.stl  (supports: no)
  - clip_LC_spacer_glove_spacer_16mm.stl  (supports: no)

HOW IT MOUNTS
  BACKSTAGE CART LIP (ONE PIECE, STRONGEST)
    The cart-lip slot is printed into the holder, so it is one piece and as strong as it gets.
    Hold it tilted, hook the slot over the upright lip on the edge of a Magliner / Backstage-style cart
    shelf, and rock it down until it sits flat against the side.

    Notes for this holder: Default: one piece with the Magliner/cart lip block (shipped part), strongest. Prints upright with build-plate tree supports under the inner flange. Spacers and size tags as needed. Also included: other sizes and parts (clip_LC_long_glove_box_sleeve_long.stl, clip_LC_spacer_glove_spacer_16mm.stl).

HOW IT WORKS
  Holds a box of disposable nitrile gloves on the cart side, so it doesn't get crushed in a drawer or blow away.
  How it works: the box stands on its long edge with its back against the plate and the dispensing hole facing out. Drop it in from the top. 80 mm end walls (90 mm on the long sleeve, about 70 % of the box height) with 24 mm front corner returns and a 22 mm bottom rail hold it, and the whole dispensing face stays open. Pull gloves out of the front. As the box empties they settle along the bottom, just above the rail. The box top stands above the walls, so you can lift it out one-handed.
  No rattle on the standard sleeve: a common 218-221 x 61 mm box is smaller than the sleeve, so the standard sleeve comes with two drop-in spacers. The 6 mm back spacer goes behind the box, and then the 1.2 mm ramp nubs on the returns leave only about 0.3 mm of play in and out. The 13 mm end spacer goes in one end and leaves 1-4 mm of play along the sleeve. Without the spacers the box can shuffle about 6 mm in and out and 14-17 mm along the sleeve.
  Size tag: slide an S, M, L or XL tag down the dovetail slot in the left return. Print it in a contrasting colour. Each tag is 18.5 x 40 mm with a raised letter and a lift hole.
  Sizes (measure your box):

  - Standard: boxes up to 233 long x 66 thick (most 9 x 5 x 2.5 in 100-count boxes, e.g. about 218-221 x 112-114 x 61 mm). Inside 235 x 68.5 mm. For a 218-221 x 61 mm box, add the 6 mm back spacer and the 13 mm end spacer.
  - Long: boxes 238-250 long and up to 82 thick (N-DEX and Kimberly-Clark class, about 248 x 130 x 67-82 mm). Inside 250 x 84 mm. For a box under 68 mm thick, drop the 16 mm spacer in behind it.
  Cart facts

  - Sticks out from the cart side: 81.5 mm (standard) / 97 mm (long), with the box inside the outline
  - Hangs below the deck: 96 mm (standard) / 110 mm (long). The box top stands about 20-35 mm above the deck.
  - Flat cart side needed below the lip: 45 mm. Below that the back is set 2.5 mm off the cart side.
  - Two M5 insert holes in the 120 mm mount block
  Retention: held by gravity unless you fit the M5 thumbscrew. A short M5 heat-set insert (6.4 mm hole, 9 deep) goes into the deck-side face of the inner flange; a nylon-tipped M5 thumbscrew through it clamps the lip, so the part cannot lift off on a bump, slide along the lip or rattle. Check your lip is at least 16 mm tall first.
  Fits: Backstage Equipment and Magliner-style carts with a 3.4 mm upright shelf lip. The mount drops onto the lip from above: 3.7 mm slot (0.3 mm clearance), 26.6 mm deep with a round end, 0.5 mm chamfers at both slot ends.

OTHER MOUNTS
  The same holder also comes ToughBuilt bar (one piece), Dock (swap between mounts), Mountless (desk, shelf, case or screw to a panel). Pick the mount on the site: https://cart-tools.sdos-placeholder.workers.dev/#lc-std-glove-box-sleeve-std

TEST THE FIT FIRST
  Carts, bars and tape rolls vary a little. Before a long print, print the small fit test from the
  Test pieces section of the site (or this part at low infill) and check it on your own gear.

Not affiliated with or endorsed by Magliner, Backstage Equipment, ToughBuilt, Milwaukee, Hollyland, Eartec, Sekonic, Inovativ, Matthews or Manfrotto. Brand names only say what a holder fits.
