Blank Tape Label Plate - Backstage cart lip (one piece, strongest)
==================================================================

What it holds: Blank plate for 2 in paper tape

PRINT SETTINGS
  Filament:  PETG
  Walls:     5
  Infill:    35% gyroid
  Orientation: the files are already oriented for printing. Put them on the plate as they load;
               don't rotate them.

FILES AND SUPPORTS
  - clip_HG_blank_tape_plate.stl  (supports: no)
  - clip_HG_blank_tape_plate_1in.stl  (supports: no)
  - clip_HZ_label_fit_test.stl  (supports: no)

HOW IT MOUNTS
  BACKSTAGE CART LIP (ONE PIECE, STRONGEST)
    The cart-lip slot is printed into the holder, so it is one piece and as strong as it gets.
    Hold it tilted, hook the slot over the upright lip on the edge of a Magliner / Backstage-style cart
    shelf, and rock it down until it sits flat against the side.

    Notes for this holder: Two plates: 2 in (52 mm tape band, 60 tall) and 1 in (27 mm band, 45 tall). Native one-piece cart-lip mount (strongest): drops onto the Magliner/Backstage lip, two crush ribs hold it, optional M4 heat-set insert + thumbscrew. Prints upright, no supports. clip_HZ_label_fit_test.stl is the 20 mm crush-rib fit test, print it first.

HOW IT WORKS
  A blank label plate for tape. The plate has a 0.6 mm recessed band: lay a strip of paper tape or gaffer in it and write on it, such as A CAM, B CAM, 2ND UNIT, a name or the show. The recess keeps the tape edges from being peeled up by passing gear, and a fresh strip relabels it for the next job. The tape goes on the plate, never on the cart, so it is fine on rental carts.
  Two sizes:

  - 2 in tape: 140 x 60 mm plate with a 52 mm band
  - 1 in tape: 140 x 45 mm plate with a 27 mm band
  Both sit flush in front of the lip on an 80 mm mount. The wings come back to 0.3 mm off the lip, so nothing can hook behind them in a doorway, and the plate ends are chamfered 45 degrees. Leave 35 mm of clear lip each side of the mount (no other clip under the wings).
  Cart facts

  - Sticks out 13 mm from the cart side
  - Hangs 0 mm below the deck
  - Flat cart side needed below the lip: none (nothing hangs below the deck)
  - Plate stands 60 mm (2 in) or 45 mm (1 in) above the deck
  - Overall 30.7 x 140 x 60 mm (2 in) or 30.7 x 140 x 45 mm (1 in)
  Retention: held by gravity unless you fit the M4 thumbscrew (this family uses M4 instead of the M5 used on the bins). A short M4 heat-set insert (5.6 mm hole, 8 deep) goes into the deck-side face of the inner flange; a nylon-tipped M4 thumbscrew clamps the lip. Two small crush ribs in the slot (0.1 mm press fit on the lip) stop rattle on their own.
  Fits: Backstage Equipment and Magliner-style carts with a 3.4 mm upright shelf lip. The mount drops onto the lip from above: 3.7 mm slot (0.3 mm clearance), 26.6 mm deep with a round end, 0.5 mm chamfers at both slot ends.

OTHER MOUNTS
  The same holder also comes ToughBuilt bar (one piece), Dock (swap between mounts), Mountless (desk, shelf, case or screw to a panel). Pick the mount on the site: https://cart-tools.sdos-placeholder.workers.dev/#hg-blank-tape-plate

TEST THE FIT FIRST
  Carts, bars and tape rolls vary a little. Before a long print, print the small fit test from the
  Test pieces section of the site (or this part at low infill) and check it on your own gear.

Not affiliated with or endorsed by Magliner, Backstage Equipment, ToughBuilt, Milwaukee, Hollyland, Eartec, Sekonic, Inovativ, Matthews or Manfrotto. Brand names only say what a holder fits.
