Solidcom Headset Saddle (BB-1) - ToughBuilt bar (one piece)
===========================================================

What it holds: Hollyland Solidcom C1 / C1 Pro headset saddle with cup cradle on the BB-1 dovetail for the ToughBuilt box bar.

PRINT SETTINGS
  Filament:  PETG
  Walls:     5
  Infill:    35% gyroid
  Orientation: the files are already oriented for printing. Put them on the plate as they load;
               don't rotate them.

FILES AND SUPPORTS
  - HA_C1_saddle_toughbuilt_T2p5.stl  (supports: no (unless your slicer warns))
  - HA_C1_saddle_toughbuilt_T7p65.stl  (supports: no (unless your slicer warns))
  - HA_C1_cradle.stl  (supports: no (unless your slicer warns))
  - HA_C1_saddle_BB1.stl  (supports: no (unless your slicer warns))
  - HA_C2_saddle_BB1.stl  (supports: no (unless your slicer warns))

HOW IT MOUNTS
  TOUGHBUILT BAR (ONE PIECE)
    The ToughBuilt StackTech / ClipTech bar hook is printed into the holder (one piece).
    Files with _toughbuilt_T2p5 / _toughbuilt_T7p65 in the name are the same holder with two throat
    sizes: print ONE. T2p5 for a thin (about 2 mm) steel edge, T7p65 for a 7.3 mm edge. If unsure, print
    the ToughBuilt fit coupon from the Test pieces section first. An M5 heat-set insert and an M5
    cup-point set screw clamp it to the bar.

    Notes for this holder: One piece with the ToughBuilt StackTech / ClipTech bar back: hooks over the top edge of the steel plate, holder hangs 6 mm below the plate edge and stands 6 mm off the plate face. Pick the throat that fits your plate after printing TB_fit_coupon (20_toughbuilt): T2p5 for the thin ~2 mm steel edge, T7p65 if the edge is 7.3 mm. Clamp: M5 short heat-set insert + M5 cup-point set screw from the front of the hook block (M5 x 16; M5 x 20 for T7p65 on ~2 mm steel), 2.5 mm hex. Prints on its end like the lip version, no supports. (The two-piece BB-1 version - HA_C1_saddle_BB1 on 20_toughbuilt BB1_bar_back - stays available as this card's main download.) Also included: the earlier ToughBuilt bar version (HA_C1_saddle_BB1.stl, HA_C2_saddle_BB1.stl).

HOW IT WORKS
  The Solidcom headset saddles for the steel bar on a ToughBuilt box or cart. The Magliner mount block is replaced by the segmented dovetail that drops onto our BB-1 bar back block (family 20, print and fit that first).

  - C1 version: fits the Solidcom C1 and C1 Pro single-ear headsets
  - C2 version: the C1 Pro dual-ear headset (size estimated, see the cart listing)
  Numbers

  - Sticks out about 117 mm in front of the bar plate with the cradle (BB-1 adds 15 mm)
  - About 181 g (C1) / 193 g (C2) plus the cradle (PETG estimate)
  - The panel hangs about 140 mm below the bar's top edge: check the box face below the bar is clear

OTHER MOUNTS
  The same holder also comes Backstage cart lip (one piece, strongest), Dock (swap between mounts), Mountless (desk, shelf, case or screw to a panel). Pick the mount on the site: https://cart-tools.sdos-placeholder.workers.dev/#ha-c1-saddle-bb1

TEST THE FIT FIRST
  Carts, bars and tape rolls vary a little. Before a long print, print the small fit test from the
  Test pieces section of the site (or this part at low infill) and check it on your own gear.

Not affiliated with or endorsed by Magliner, Backstage Equipment, ToughBuilt, Milwaukee, Hollyland, Eartec, Sekonic, Inovativ, Matthews or Manfrotto. Brand names only say what a holder fits.
