Eartec Battery Station (FRESH / DEAD) - Backstage cart lip (one piece, strongest)
======================================================================

What it holds: Ten LX600Li packs on end, split FRESH and DEAD, with snap channels underneath that run the charger lead to the power strip.

PRINT SETTINGS
  Filament:  PETG
  Walls:     5
  Infill:    35% gyroid
  Orientation: the files are already oriented for printing. Put them on the plate as they load;
               don't rotate them.

FILES AND SUPPORTS
  - EC_battery_dock_fresh_dead.stl  (supports: no)
      how it lies on the plate: standing on the y0 end face (STL already oriented), no supports

HOW IT MOUNTS
  BACKSTAGE CART LIP (ONE PIECE, STRONGEST)
    The cart-lip slot is printed into the holder, so it is one piece and as strong as it gets.
    Hold it tilted, hook the slot over the upright lip on the edge of a Magliner / Backstage-style cart
    shelf, and rock it down until it sits flat against the side.

    Notes for this holder: One piece with the Magliner/cart lip block (shipped part).

HOW IT WORKS
  Battery swaps on an Eartec kit without the guesswork: charged packs on one side, flat ones on the other.
  What it holds
  Ten Eartec LX600Li packs standing on end, 18 mm proud: five in the FRESH half and five in the DEAD half, with the words engraved on the front and a gap between the halves. Take a pack from FRESH, drop the flat one into DEAD, and whoever runs the charger knows what to charge. The LX600Li fits the UltraLITE and UltraLITE HD headsets, the UltraPAK beltpack and the HUB.
  One-handed grab
  Every slot has a 10 mm deep scallop in the front wall for your thumb and another in the back wall for a fingertip, with 11 mm of room behind each pack. Pinch the pack front and back and lift, gloves on. The ribs between the packs are 6 mm.
  Charger lead
  Two snap channels run the full length underneath, mouths facing out: a 4.2 mm one for the charger's DC lead and a 7.2 mm one for the adapter or mains cord. Press the cable in from the front and it runs along the cart edge to the power strip (the power-strip saddles in the Village set), so the multi-charger can sit on the cart top with its cable out of the way.
  Check first: measure one pack. Each slot is 12.4 x 34.4 mm inside and 22 mm deep, drawn from a published 40.1 x 33.0 x 11.1 mm replacement pack. Eartec does not publish the original's size. This dock does NOT fit the EVADE EX1000Li or PRO16 LX950Li packs (sizes unknown). Also measure your charger's DC lead and the adapter cord: the channels take 4.2 mm and 7.2 mm cords, and a lead much thinner than about 4 mm will not stay in.
  Numbers

  - Sticks out 56 mm from the cart side (the part itself)
  - Hangs 45 mm below the deck; the block top stands 42 mm above it
  - Takes 191 mm of the lip; needs 45 mm of flat cart side below the lip for the back plate
  - Each slot has a drain hole in the floor
  - 74 x 191 x 87 mm (out x along the cart x tall)

OTHER MOUNTS
  The same holder also comes ToughBuilt bar (one piece), Dock (swap between mounts), Mountless (desk, shelf, case or screw to a panel). Pick the mount on the site: https://cart-tools.sdos-placeholder.workers.dev/#ec-battery-dock-fresh-dead

TEST THE FIT FIRST
  Carts, bars and tape rolls vary a little. Before a long print, print the small fit test from the
  Test pieces section of the site (or this part at low infill) and check it on your own gear.

Not affiliated with or endorsed by Magliner, Backstage Equipment, ToughBuilt, Milwaukee, Hollyland, Eartec, Sekonic, Inovativ, Matthews or Manfrotto. Brand names only say what a holder fits.
